{"id":31028,"date":"2026-11-10T16:44:54","date_gmt":"2026-11-10T08:44:54","guid":{"rendered":"https:\/\/safetyfencesystems.com\/blog\/machine-containment-guarding-polycarbonate-panels-projectile\/"},"modified":"2026-11-10T16:44:54","modified_gmt":"2026-11-10T08:44:54","slug":"paineis-de-policarbonato-de-contencao-de-maquinas-contra-projeteis","status":"publish","type":"post","link":"https:\/\/safetyfencesystems.com\/pt\/blog\/paineis-de-policarbonato-de-contencao-de-maquinas-contra-projeteis\/","title":{"rendered":"Prote\u00e7\u00e3o de M\u00e1quinas por Conten\u00e7\u00e3o: Quando Pain\u00e9is de Prote\u00e7\u00e3o de M\u00e1quinas em Policarbonato Substituem a Tela Met\u00e1lica"},"content":{"rendered":"
\n
\n

MACHINE CONTAINMENT GUARDING \/ INTERNAL PROJECTILES \/ PANEL SELECTION<\/p>\n

A fence that keeps people out can still let a broken tool leave the cell<\/h2>\n

Most perimeter guarding is specified to stop a person reaching a hazard. A bearing race, a broken insert or a workpiece ejected from a chuck is a different problem: the energy comes from inside, it travels outward, and an open mesh that satisfies a reach-distance table may not stop it. Machine containment guarding starts by classifying the projectile and its energy, then choosing between narrow-aperture framed mesh, a solid steel sheet and polycarbonate machine guard panels. The result is an enclosure designed around what the machine can throw, not a line drawn around its footprint.<\/p>\n

\n \"Solid
\n <\/figure>\n

Send your ejection risk assessment for a panel schedule<\/a><\/p>\n<\/section>\n

\n

Two load cases that are not interchangeable<\/h2>\n

External vehicle impact pushes into the cell; an internal projectile pushes out. The first is checked as a cantilever down to the anchors. The second is checked as local penetration and panel retention, including what happens at the frame, the fixings and the seams.<\/p>\n

\n\n\n\n\n\n\n\n\n\n
Load case<\/th>\nWhat governs the panel choice<\/th>\n<\/tr>\n<\/thead>\n
Forklift or AGV contact from outside<\/th>\nPost bending, base plate and anchor pull-out; framed mesh and the Q235 skeleton carry it.<\/td>\n<\/tr>\n
Workpiece, tool fragment or grinding wheel from inside<\/th>\nAperture size, wire diameter, panel retention and whether a closed infill is required.<\/td>\n<\/tr>\n
Combined risk on one cell<\/th>\nZone the enclosure: solid or polycarbonate panels opposite the spindle, framed mesh on low-risk sides.<\/td>\n<\/tr>\n
Visibility and inspection<\/th>\nSolid sheet blocks sightlines; polycarbonate machine guard panels keep the process visible.<\/td>\n<\/tr>\n
Heat and fire near the process<\/th>\nPlastic panels are rated to 60 °C and listed to UL94 V0 and EN 1598; above that, use steel.<\/td>\n<\/tr>\n<\/tbody>\n<\/table><\/div>\n<\/section>\n
\n

Choosing the surface that faces the hazard<\/h2>\n
\n

Start with the aperture, not the wall thickness<\/h3>\n

A 20×100 mm mesh with 4.0 mm wire in a 20x30x1.5 mm tube frame is the standard starting point for internal interception: the narrow slot limits what can pass and the welded border keeps the sheet in its clamps. It is a real containment layer for chips and small fragments, not merely a boundary marker. Where the risk assessment names a heavier ejected part, the aperture alone is not enough evidence and the panel has to be upgraded.<\/p>\n

\"Black<\/figure>\n<\/article>\n
\n

When a solid infill is mandatory<\/h3>\n

High-energy ejection, grinding wheel failure, press tooling breakage and coolant jets at pressure call for a closed surface. Steel or aluminium sheet is the default where heat, sharp fragments or hot swarf are present. Polycarbonate machine guard panels are used where the process must stay visible or where a transparent barrier supports inspection. Both are fitted as module infills on the same frame system, so a cell can mix mesh and closed panels along one run instead of switching to a bespoke enclosure.<\/p>\n

\"Robot<\/figure>\n<\/article>\n
\n

Where the plastic panel stops<\/h3>\n

Product documentation gives a 60 °C heat limit for plastic panels and lists UL94 V0 and EN 1598 fire behaviour. Those are boundaries, not a general-purpose rating: a welding station with hot spatter, a furnace cell or a wash-down line with aggressive cleaners belongs on steel or on a specified high-temperature glazing. We do not claim a plastic infill contains a workpiece from a failed fixture. The containment case has to be stated in the risk assessment and matched to a tested panel, with the acceptance evidence supplied for that configuration.<\/p>\n

\"Industrial<\/figure>\n<\/article>\n<\/section>\n
\n

Cells that usually need a containment decision<\/h2>\n